Mold Production Of Ceramic Products does not appear to be shot and the shot does not move the fault
For Mold Production Of Ceramic Products, if it is not the phenomenon of non-gel, we have to know to see it's shot coil electromagnetic coil is not the phenomenon of burnout, or there are foreign objects into our directional valve, In addition, it is to be moved with the spool, or it will be replaced for the plastic injection valve; or, for Mold Production Of Ceramic Products, the pressure is too low, it is necessary to increase the pressure of injection can be.
For Mold Production Of Ceramic Products does not appear in the case of plastic injection, the injection of the temperature is relatively low, this time is to adjust the thermometer for our temperature directly to the requirements of the point on it. But adjust the thermometer or can not increase its temperature, it is necessary to check the electric heater and the fuse to see if it is not burned or loose phenomenon, if it has been broken, but also to be replaced in a timely manner of.
For Mold Production Of Ceramic Products, its sol screw rotates and, in the case of its compound, it can not enter the barrel. In general, the back pressure of the sol after its sol is relatively high, it is necessary to adjust or replace the sol backpressure valve when it is damaged or improperly adjusted.
Mold Production Of Ceramic Products shot of the phenomenon does not move, then for its shot limit limit stroke switch is concerned, but also will be adjusted to hit the block pressure, then the direct adjustment can be; for the shooting table The solenoid valve coil is also possible to have burned out or there is a foreign object into the direction of the valve to carry the card to move the spool, then we need to clean its solenoid valve or replace.
When the shooting of Mold Production Of Ceramic Products does not move, the speed of the advancement of the shoots is checked and the pressure is not suitable for the adjustment. Moreover, the I / O board for Mold Production Of Ceramic Products , The direction of its valve output voltage is to be checked to see if it is not normal, if it is not normal, it should be the output of the transistor or relay, etc. to see if it is not already damaged.
Under normal circumstances, Mold Production Of Ceramic Products in the brittle cutting effect, in fact, much better than plastic, and can more easily meet the relevant processing requirements, but for the same material, in the metallographic structure, if it is The smaller the words, then the better, this point in the industry are more recognized.
First, Mold Production Of Ceramic Products In forging equipment, if it is based on the weight of the forging classification, then it is best to use tonnage larger mold or equipment, and in forging should be used before the hammer or hammer drill Preheating the mold in advance to ensure the good operation of the production process.
Second, Mold Production Of Ceramic Products in the preparation of the blank powder, the blank at the time of cutting, it is best to carry out cold saw, and according to the different requirements of Mold Production Of Ceramic Products, in the choice of raw materials, should be in accordance with the level To choose, different materials using different molds, so that the processing will be more accurate.
Third, Mold Production Of Ceramic Products The heating of the blank, the heating of the blank, it is best to slow to prevent the rapid heating of the way to avoid the phenomenon of burning, and in the heating process, the temperature should not be limited The lower limit, if there burned the case, it should first be cooled and then in the forging.
If you want to heat a number of Mold Production Of Ceramic Products, between each piece and each piece, you must ensure that there is a certain gap during heating, and that the parts must be flipped throughout the heating process to ensure that They will not appear between each other bonding, to ensure that the product processing and use of normal.
After the cutting Mold Production Of Ceramic Products in the contours and shape is still relatively poor degree of roughness, and pure structure and made from the contours of a large difference, mainly because of the cutting process, the plastic appeared Serious deformation, and we in the cutting time, the choice of the tool is also more important.
Because the different tools in the precision, as well as fine cutting high and low speed will have an impact, seriously will affect the normal use of the Mold Production Of Ceramic Products. If the brittle Mold Production Of Ceramic Products material processing, then the rate of cutting for the roughness of the impact is not large.